|
Painted
Accessories |
|
|
Click on image to enlarge |
Use your browsers "Back"
button to return to this page |
 |
 |
53301 WINDSHIELD WASHER RESERVOIR COVER $225.00
Constructed of form fitting fiberglass.
Painted in your choice of factory colors. 97-04
• INSTALLATION INSTRUCTIONS •
Held in place by Velcro strips. |
|
|
 |
53301F WINDSHIELD WASHER RESERVOIR COVER $TBD
Information to Come
• INSTALLATION INSTRUCTIONS •
This |
|
|
 |
53302 RADIATOR SURGE TANK COVER $225.00
Constructed of form fitting fiberglass.
Painted in your choice of factory colors. 97-04
• INSTALLATION INSTRUCTIONS •
Held in place by Velcro strips. |
|
|
|
|
53302F RADIATOR SURGE TANK COVER $TBD
Information to Come
• INSTALLATION INSTRUCTIONS •
This |
|
|
 |
53303 UPPER RADIATOR SUPPORT $275.00
OEM part painted in your choice of
factory colors 97-04.
• INSTALLATION INSTRUCTIONS •
1. Remove air duct and four bolts holding support and remove support.
2. Install painted support in reverse procedure. |
|
|
 |
53307 FENDER COVE MOLDINGS (PAIR) $199.99
Constructed of OEM ABS. Painted in your
choice of factory colors 97-04. Held in place by 3M automotive double
sided tape.
• INSTALLATION INSTRUCTIONS •
1. Clean the area that the moldings will be applied to with denatured
alcohol.
2. Apply template to fender using tape at the four marked locations on
the template.
3. Line up the template with the door edge of the fender, the top of
the cove as it begins to roll inward and at the bottom of the cove
opening as indicated on the template.
4. Make certain the template is aligned and the molding openings are
straight and to your satisfaction before you install the moldings.
They can not be easily removed once installed.
5. Peel the backing from the molding and apply it to each opening in
the template. Apply pressure with the heel of your hand to the molding
to insure good adhesion to the fender.
6. Reverse the template for the passenger side and follow steps 1 thru
5 above. |
|
|
 |
53308 FRONT LICENSE BRACKET ASSEMBLY $99.00
OEM License bracket painted in your
choice of factory colors 97-04. Comes with clear acrylic license plate
cover and four chrome screw cap covers.
• INSTALLATION INSTRUCTIONS •
Insert supplied clear plastic lens into bracket. Next, insert the
state license into bracket behind the clear plastic lens. Install the
two 1/4" x 1/2" supplied screws, two plastic chrome cap retainers and
two 1/4" nuts through the top two holes of the license plate and clear
plastic lens. Install the bracket assembly on the car by sliding the
top of bracket assembly into the factory slots on the top of the
license recessed area on the car. Push the bottom of the bracket
toward the car until the bottom holes align. Install the two original
screws into these holes after following the instructions supplied with
the chrome screw covers. |
|
|
|
|
53311 WIPER COWL PANEL $325.00
INFORMATION TO COME
• INSTALLATION INSTRUCTIONS •
This
|
|
|
|
|
53315 C5 GAS DOOR BOOT $125.00
INFORMATION TO COME
• INSTALLATION INSTRUCTIONS •
This
|
|
|
|
53316 FRONT SPOILER $TBD
INFORMATION TO COME
• INSTALLATION INSTRUCTIONS •
This
|
|
|
 |
53317 SIDE SKIRTS $TBD
INFORMATION TO COME
• INSTALLATION INSTRUCTIONS •
This
|
|
|
 |
54002 LSD Vertical Doors $TBD
INFORMATION TO COME
• INSTALLATION INSTRUCTIONS •
This
|
|
|
 |
54003 Fender Strips $TBD
INFORMATION TO COME
• INSTALLATION INSTRUCTIONS •
This
|
|
|
 |
63136 PAINTED DOOR HANDLES
$TBD
Information to Come
• INSTALLATION INSTRUCTIONS •
This |
|
|
 |
63139
FENDER COVE MOLDING $239.00
This area begs for something to be there and these molding look like they should have come from the factory. This set of 6 moldings are the same OEM type as GM uses on other cars. They are held in place with 3M tape for a permanent bond. They come painted in your choice of factory colors to match your body. Installation time is about 20 minutes per side. Fits 2005-2008
• INSTALLATION INSTRUCTIONS •
Simply remove the protective backing from the 3M tape and place in desired position.
|
|
|
 |
63140
REAR LICENSE MOLDING $239.00
This set of 6 moldings fill that conspicious void on both sides of your license plate. Why didn't the factory think of this. These molding are the same OEM type that GM uses on other cars. They are held in place with attached 3M tape for a permanent bond. They come painted in your choice of factory colors to match your body. Installation time is about 20-30 minutes. Fits 2005-2008
• INSTALLATION INSTRUCTIONS •
This
|
|
|
 |
63141 LOWER REAR BUMPER $TBD
Information to Come
• INSTALLATION INSTRUCTIONS •
This |
|
|
| |
|
|
To order, phone 804-763-6288.
We accept VISA, MasterCard, money orders and checks
and remember...CHROME WINS!!!
|
|
Tip: For best
appearance and long life always keep a good coat of wax on all chrome
parts.
Creative Engine
Covers, Inc. is not responsible for injury to persons or damages to
property resulting from the use of these parts.
|
