Page  1  |  2  |  3  |  4  |  5 

This hand formed 14 ga. steel "show quality" triple chrome plated piece transforms your drab alternator into a chrome plated work of art. Simple installation requires no modifications to your Corvette. Alternator covers are supported by welded brackets and / or velcro that easily attach to existing hardware. Folks, these are the finest chrome accessories you’ll find! Installation time is about 10 minutes. Fits 2005-2008

• INSTALLATION INSTRUCTIONS •
DISCONECT BATTERY BEFORE BEGINNING 1.Loosen top alternator mounting bolt far enough for the slotted bracket on the Chrome Alternator Cover to slide between the alternator and bolt head. 2.Place the Chrome Alternator Cover in position over the alternator with the bracket in the correct position on the bolt, lower the Chrome Cover until it touches the alternator. 3. Mark the location where it touches on both the alternator and the Chrome Cover. 4. Remove the Chrome Cover and secure the supplied Velcro to both the alternator and the Chrome Cover at these locations. (Make sure this location is clean of any greese or dirt so the Velcro adhesive will stick properly) 5. Replace the Chrome Cover on the alternator with the bracket firmly against the bolt and lower the Cover down and firmly press on it in the area of the Velcro to make sure the two pieces attach. 6. Tighten alternator bolt.

Hand crafted from 16 ga. steel, "show quality" triple chrome plated for an award winning look. This piece easliy slips over your existing fuse box and is held in place with Velcro strips for easy removal if you need to access yor fuses. Installs in under 3 minutes. Fits 2005-2008

• INSTALLATION INSTRUCTIONS •
1. Clean the top of your fuse box with denatured alcohol to remove any previously applied silicone products that will prevent the Velcro from adhereing properly. 2. Slide the Chrome Fuse Box Cover over your fuse box until it is down as far as it will go. When you are satisfied with the way it looks and fits remove the Chrome Cover. 3. Peel the protective film from the attached Velcro ( DO NOT SEPERATE THE VELCRO HALVES) and slide the Chrome Cover over your fuse box as before. Press firmly on the area of the Velcro to make sure it adheres to your fuse box. Do not remove cover for 24 hours to give the Velcro adhesive time to cure.

• INSTALLATION INSTRUCTIONS •
1. Clean top of brake booster with denatured alcohol.
2. Remove backing from self adhesive tape on back of cover.
3. Position cover evenly over brake booster.
4. Gently lower cover onto brake booster being careful to have equal amounts of cover on both sides of brake booster.
5. Apply even pressure to cover to adhere tape. Vehicle may be driven immediately but allow tape adhesive to cure for 24 hours.

• INSTALLATION INSTRUCTIONS •
1. Remove all grease and brake fluid from the outside of the master cylinder.
2. Remove fill cap from master cylinder.
3. Install Chrome Cover by positioning it over the master cylinder, align the hole in cover with master cylinder fill hole, press cover straight down until cover seats on top of master cylinder ---- cover was designed for a tight fit, installer may have to rock cover back and forth while applying downward pressure for proper fit.
4. Replace cap on master cylinder fill hole.

This 15 piece kit uses factory replacement retainers with chrome caps attached. These are larger in diameter than the originals but are of a lower profile to clear most after market accessories that you may have on your engine when the hood is closed. This kit will truley brighten up your drab black hood liner and if you have a painted logo it makes it come alive. Installation time is about 15 minutes. Fits 2005-2008.

• INSTALLATION INSTRUCTIONS •
1. Remove your hood liner retainers with a retainer removal tool or by grasping the retainer with your finger tips and pulling the retainer straight out from the hood. (be careful not to damage your hood liner as it is soft and unforgiving). 2. Replace each retainer with a Chrome Retainer as you go by inserting the serrated tip into the hole and pressing the retainer in as far as it will go with your thumb.. Only remove one retainer and replace it with a Chrome Retainer at a time.

These strut covers are machined from billet aluminum, highly polished and then "show quality" triple chrome plated for a professional look. These are not slip on stainless tubes, these are the real deal. Installation time is about 10 minutes. Fits 2005-2008

• INSTALLATION INSTRUCTIONS •
1. Remove by inserting a small screw driver blade under the metal clip on each end of the strut and prying the clip outward while pulling the strut away from the ball nut that it is attached to. 2. Each end of the strut will "pop" off of the ball nut. Make sure that you support the hood so that it doesn't close when you remove the strut. 3. To install the new chrome strut cover, simply place a piece of masking tape on the whole length of the barrel of your strut and add aditional pieces as necessary to make a tight fit when you slide the cover over the strut barrel. 4. To reinstall the strut make sure you place the correct end over the ball nut and press it on with your hand. Do one end at a time.  

• INSTALLATION INSTRUCTIONS •
1. Remove the two bolts from the existing striker and remove striker.
2. Replace with chrome striker and chrome replacement bolts and washers. 

• INSTALLATION INSTRUCTIONS •
1. Remove bolts from hinge and scribe the inner hole onto frame, one bolt at a time, replacing the bolt after scribing the mark.
2. After scribing all holes, remove all bolts and hinge.
3. Replace with chrome hinge, aligning holes to scribe marks.
4. Reinstall bolts.

This kit consists of 4 each replacement hex head bolts and 4 each hardened steel washers for the hood, 4 each hardened washers, 4 each hex head lock nuts and 4 each acorn nuts for the frame. All of these are chrome plated ..... no stainless steel here. Fits 2005-2008

• INSTALLATION INSTRUCTIONS •
1. Remove existing bolts one at a time marking the location of the inside hole in the hinge onto the frame and the hood. Also mark the out side of the hinge on both the frame and the hood. A # 2 lead pencil works well for this. 2. As you remove the first hinge have some one hold the hood while you install the new chrome hinge. 3. To install the new chrome hinge make sure the new hinge and holes match your marks on both the frame and hood before tightning the bolts. 4. Repeat the above procedures for the second hinge. 5. The hood should be in perfect alignment if you matched your markings. If not simply loosen the appropriate bolts and adjust the hood to your satisfaction.  

• INSTALLATION INSTRUCTIONS •
1. Remove bolts from latch and scribe the inner hole onto frame, one bolt at a time, replacing the bolt after scribing the mark.
2. After scribing all holes, remove all bolts and latch.
3. Replace with chrome latch, aligning holes to scribe marks.
4. Reinstall bolts. 5. Follow above directions for second latch.

Page  1  |  2  |  3  |  4  |  5 

DISCLAIMER User accepts any and all liabilities resulting from the use of Creative Engine Covers, Inc. products. Creative Engine Covers, Inc. is not liable for damages to property or injury to persons resulting from the use of our products. The user agrees to these terms by the act of using these products.