Page  1  |  2  |  3  |  4  |  5  |  6  |  7  |  8 

50160 BATTERY COMPARTMENT COVER $184.00

This piece really makes the battery compartment area stand tall. Lazer cut from 18 ga. steel and "show quality" triple chrome plated for a show winning look. There are thirteen slots in this cover that match the slots in our Cowl Insert, Item 50137. For a dynamite look, use our regular Battery Cover, Item # 50104 under this Compartment Cover with an emblem placed on the top of the regular Battery Cover so it can be seen when looking down through the slots of the Battery Compartment Cover. WOW !!! Installation time is about 15 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove the rubber weather strip gasket from the battery compartment by grasping it on one end and pulling it straight up until it seperates from the battery compartment wall.
2. Insert the back end of the Battery Compartment Cover under the cowl and lower the cover so that it rests on the lip in the battery compartment wall and on the base of the rubber hood bumper at right rear. The left front corner of the cover will not rest on the battery compartment lip at this time. The rubber weather strip gasket will hold this corner down on the lip when you reinstall it.
3. When the cover is in place and seems to look like it is aligned properly, remove the cover and peel the protective film from the three Velcro strips. DO NOT SEPERATE THE VELCRO HALVES. Reinstall cover as before while pressing the side of the plastic battery compartment wall tight against the cover and press down in the area of the Velcro so it will adhere to the lip on the side of the battery compartmeny wall and be tight against the side of the wall. Reinstall the rubber weather strip by starting at one end and pressing it down onto the edge of the battery compartment wall as you work toward the other end.

INSTALLATION INSTRUCTIONS
These are very easy to install. Before you begin, mark the positipn of your wiper blades by applying a strip of tape on your windshield next to your blades. 1. Remove the wiper arm nut cap by pulling straight up with your finger tips.
2.Remove the nut holding the arm to the stud.
3. Raise the wiper arm up and away from the windshield and while holding it in this position with one hand place the fingers of your other hand under the arm where it slips over the stud and forceably pull it up and off of the stud. Some times they may be stuck and you will have to jerk on it but be sure you are pulling straight up and not putting it in a bind by pulling it crooked.
4. Install the Chrome Wiper Arm by slipping it over the stud and pushing it all the way down making sure the blade aligns with the tape on the windshield. When you are satisfied with the way it looks and fits, install the nut and tighten, install the replacement nut cap.
5. Replace the other side following the above instructions.

These are factory original pieces that have gone through our special chroming process that transforms the ugly texured black plastic to beautiful smooth "show quality" triple chrome plated pieces. These compliment our Chrome Door Strikers, Item 50133. If you open your doors at shows, you really need these. Installation time is about 10 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
These are really simple to install. 1. Remove the existing striker bezels by carefully inserting a thin blade screw driver behind the striker bezel and with a twisting motion, pry the striker bezel away from the door jam. When you can get your finger tips under it just pull it off of the door jam. It is only held on with hook and loop material. YOU DO NOT HAVE TO REMOVE THE DOOR STRIKER !!!
2. To install the Chrome Door Striker Bezel, simply position new hook and loop material on bezel and press bezel over the striker making sure the bezel fits tightly against the door jam.
3. Repeat above procedure for the second bezel.

These are factory original OEM door hinges that have been "show quality" triple chrome plated for the true show car look. If you have your doors open at shows, the judges and spectators will be amazed to see these shiney pieces. Extra things like this is what makes a winner. Installation time is about 45 minutes per door. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Mark the location of your hinges using masking tape to outline the hinges.
2. While someone helps by supporting the door perferrably by blocking it up to keep it stable and with minimal movement, remove all four bolts from the top hinge and remove the hinge.
3. Install the Chrome Top Hinge and replace the bolts making sure the hinge is in the same marked position as the original was. Open and close the door several times to make sure everything is in alignment..
4. Proceed with the bottom hinge following the same instructions as in # 2. When you are satisfied with the way it looks and fits, proceed with the other door following the same instructions.

This is a magneficant looking piece. This piece is finished in extra heavy triple plated chrome for a look you won't believe. You won't see many cars with these, so if you want something unique, this is for you. Installation time is about 10 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
This piece is very easy to install. Make sure the top of your washer tank is clean of any silicone products by wiping with denatured alcohol. 1. Remove the washer tank refill lid by lifting straight up until the retainer ring snaps off of the washer tank fill hole.
2. Simply set the Chrome Washer Tank Cover over the washer tank and gently rock back and forth until the cover slips into place. When you are satisfied with the way it looks and fits remove the Cover .
3. Remove the protective film from the attached Velcro (DO NOT SEPERATE THE VELCRO HALVES) and reposition the Cover as in step 2 , firmly press down on Cover in the area of the Velcro strips to make sure that the adhesive adheres to your washer tank. Do not remove for 24 hours to give Velcro adhesive time to cure.

This is a magneficiant looking piece. This piece is finished in extra heavy triple plated chrome for a look that you won't believe. You won't see many cars with these, so if you want something unique, this is for you. Installation time is about 10 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
This piece is very easy to install. Make sure the top of your surge tank is clean of any silicone products that might have been previously applied. Do this by wiping with denatured alcohol. 1. Remove the coolant tank fill cap.
2. Simply set the Chrome Coolant Tank Cover in place over the coolant tank.
3. When you are satisfied with the way it fits and looks remove the cover and remove the plastic film from the attached Velcro strips. ( DO NOT SEPERATE THE VELCRO HALVES ) .
4. Reposition the cover as in step 2., firmly press down on the cover in the area where the Velcro is to make sure that the adhesive on the Velcro adheres to your coolant tank. Do not remove cover for 24 hours to give the Velcro adhesive time to cure.

This is the factory orginal license plate holder. That ugly textured black plastic part has been transformed into a beautiful smooth "show quality" triple chrome plated masterpeice. This highlights your personalized licsnse plate and brightens up the front bumper like nothing else can. Installation time is about 10 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
1. Remove the two bottom screws from your original bracket, gently pull the bottom of the bracket away from the car and pull straight down. The bracket and plate will seperate from the car.
2.Install the Chrome bracket in reverse order of above removal instructions.

Page  1  |  2  |  3  |  4  |  5  |  6  |  7  |  8 
 

Creative Engine Covers, Inc. is not responsible for injury to persons or damages to property resulting from the use of these parts.