Page 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8

?

INSTALLATION INSTRUCTIONS
1. Install the supplied 1/4" x 1" hex head bolt through the unused hole in the tab on the thermostat housing. The bolt should be installed from the back side of the tab with the threaded end toward the front of the car.
2. Loosely thread the 1/4" nut onto the 1/4" bolt, leaving it loose enough so the bolt can be moved up and down.
3. Install Chrome Cover by positioning cover over idler pulley and sliding the front bracket with the 9/32" hole over the 1/4" bolt, loosely install 1/4" lock washer and 1/4" nut.------DO NOT TIGHTEN at this time.
4. Position cover so the rear bracket with the slotted hole aligns with the unused hole in the cylinder head, install the supplied flat washer and 10mm bolt.-----IT IS STRONGLY SUGGESTED TO USE A THREAD LOCKING COMPOUND such as loctite on all nuts and bolts.
5. Tighten all nuts and bolts securely, making sure to tighten the first installed 1/4" nut tight against the thermostat housing.
6. The radiator hose may cause some interference with the installation on some cars. If this is the case, simply trim the end of the hose with a razor knife. It is not necessary to remove the hose.

50107 - MASTER CYLINDER COVER $179.89

This completely covers the plastic brake fluid reservoir. This piece is a work of art, it's our hardest piece to make but our effort clearly shows. Constructed from 16 ga. steel and "show quality" triple chrome plated. Simple installation. You can use our etched chrome Master Cylinder Cap, item # 50151E for a show winning apperance. Installs in 2 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove all grease and brake fluid from the outside of the master cylinder.
2. Remove fill cap from master cylinder.
3. Install Chrome Cover by positioning it over the master cylinder, align the hole in cover with master cylinder fill hole, press cover straight down until cover seats on top of master cylinder cover.
4. Replace cap on master cylinder fill hole.

?

INSTALLATION INSTRUCTIONS
1. Loosen the top bolt in the throttle body far enough for the throttle body bracket to slide between the bolt and the throttle body. Securely tighten bolt.
2. If you are also using Creative Engine Covers Intake Cover, Item # 50101, follow above procedure except slide the throttle body bracket between the bolt and the intake bracket. Press the throttle body bracket down as far as possible and hold in that position, adjust height of intake cover. While holding both covers in desired position, securely tighten bolt. The throttle body cover may be twisted after installation slightly up, down, left or right if necessary to align with any of our additional covers or to provide additional clearances.

Laser cut from 18 ga. steel and "show quality" triple chrome plated. This piece covers the unsightly tubes coming from the anti lock brake / active handling module located beneath the upper radiator hose. This piece is held in place with attached double sided tape. Installs in about 5 minutes. Fits 2000 - 2004 with active handling only

INSTALLATION INSTRUCTIONS
1. Remove the diagonal piece of 2 inch tape from the back of the cover and set aside with the sticky side up until the final step. 2. Trial fit the ABS/AH Cover by gently lifting the top radiator hose and sliding the Cover under the hose so that it lays on top of the tubes coming out of the top of the ABS/AH module. The curved end should follow the curve of the small hose by the moldule. Make sure the edges of the Cover are square with the pulleys and covers all tubes. 3.When you are satisfied with the way the Cover fits, remove the cover and peel the protective film from the back of the two attached pieces of tape and reposition the cover as you did in the trial fit. When it is poisitioned correctly press down on the Cover to adhere the tape to the tops of the tubes. 4. Place the piece of tape that you set aside in step 1 crossways under the tubes with the sticky side up and press it into the tubes and the bottom of the tape that was attached to the cover.

This 15 piece kit is made using factory original hood liner retainers with chrome caps installed over them. This kit really makes your drab hood liner come to life. If you have a painted emblem or decal on your hood liner these retainers make them come alive. Installs in about 15 minutes. Fits 1997 to 2004.

INSTALLATION INSTRUCTIONS
1. Remove your existing hood liner retainers by inserting a retainer removal tool under the retainer or simply grasp the retainer with your finger tips and pull the retainer away from the hood until it comes out of the hole. Make sure you don't damage your hood liner as it is very soft and unforgiving. Remove one retainer at a time and replace it with a chrome retainer before proceeding to the next one. 2. Install the chrome retainer by simply inserting the pointed end into the empty hole and pressing on the chrome button end until it is fully seated against the hood liner. 3. Continue the above proceedures until all 15 chrome retainers are installed.

These chrome strut covers are machined from billet aluminum, highly polished and then "show quality" triple chrome plated. They fit perfectly over the barrel of your factory original strut. These are not the cheap thin stainless steel covers sold elsewhere. They are thick walled with machined rounded ends for a professional look. Installs in about 15 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1.Remove your hood strut by inserting a small bladed screw driver under the spring clip on the end of the strut where it attaches to the hood, gently pry this clip away from the strut end while pulling the strut away from the hood. When you have pried the spring clip far enough,the strut will come loose from the hood. You do not want to remove the spring clip entirely from the end. Repeat the above procedure for the bottom of the strut where it attaches to the frame. 2. Slide the Chrome Strut Cover over the strut until the ends align, you will notice that the Strut Cover fits very loosely. When you see how it should fit, remove the Strut Cover and wrap one or two layers of masking tape around each end of the strut barrel until the Strut Cover slides on and fits tightly. The Strut Cover will stay in place at this point. 4. Replace the strut end on the strut by screwing it on in a clock wise direction until tight. 5.Replace the strut on the car by simply pressing the strut ends over the ball sockets. There is no need to pry the spring away to reinstall. 5. Install the second strut by following the above procedure.

INSTALLATION INSTRUCTIONS
1. Remove the two bolts from the existing strikers and remove striker.
2. Replace with chrome strikers and chrome replacement bolts and washers.

INSTALLATION INSTRUCTIONS
1. Remove bolts from hinge and scribe the inner hole onto frame, one bolt at a time, replacing the bolt after scribing the mark.
2. After scribing all holes, remove all bolts and hinge.
3. Replace with chrome hinge, aligning holes to scribe marks.
4. Reinstall bolts.

This kit consits of four hardened chrome replacement washers, four chrome replacement lock bolts, four chrome acorn nuts for the hinge connection to the frame and four hardened chrome replacement washers, four chrome replacement hex head bolts for the hinge connection to the hood. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Simply unscrew the bolts from the hinge where it attaches to the hood and replace those bolts with the chrome replacement bolts and chrome washers marked "hinge to hood. 2. Remove the nuts from the hinge where it attaches to the frame and replace them with the chrome washers, chrome lock nuts and finish up by screwing the chrome acorn nut on the remaing exposed portion of the stud for a finished look. These are marked "hinge to frame".  

Page 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8
 

User accepts any and all liabilities resulting from the use of Creative Engine Covers, Inc. products. Creative Engine Covers, Inc. is not liable for damages to property or injury to persons resulting from the use of our products. The user agrees to these terms by the act of using these products.