QUALITY CHROME ACCESSORIES FOR YOUR CORVETTE
C5 Chrome Accessories
Click on image to enlarge Use your browsers "Back" button to return to this page

To order, phone 804-763-6288.
We accept VISA, MasterCard or money orders



50101 D - INTAKE COVER $399.00

This is the most important part in the engine bay. The main focus is the center of the engine. This piece is constructed from 14 ga. steel and "show quality" triple chrome plated for a show winning apperance. Installs in about 10 minutes. Fits 1997-2004. Folks, these are the finest chrome accessories youll find!"

INSTALLATION INSTRUCTIONS
1. Remove center retainer in the cowl by inserting a narrow bladed screw driver or similar instrument in the slot and gently prying the middle button up, then grasp the button with a plier and pull retainer out of hole.
2. Loosen the top bolt in the throttle body far enough for the front bracket of the cover to slide between the bolt head and throttle body.
3. Install runner cover by positioning cover under cowl until the hole in the cover lines up with the hole in the cowl. Insert 1/4-20 x 3/4 bolt through cowl hole and screw loosely into threaded hole in cover.
4. Slide slotted front bracket between throttle body and bolt head.
5. Make sure cover is aligned on both sides and tighten bolts.

50102 - ALTERNATOR COVER $189.00

Constructed of 14-gauge steel - precision cut and formed, then meticulously "show quality" triple chrome plated for a knockout look.. Simple installation requires no modifications to your Corvette. Alternator covers are supported by welded brackets and / or velcro that easily attach to existing hardware. This piece transforms your ugly alternator into a work of art. Installs in less than 10 minutes. Fits 1997-2003, 2004.

INSTALLATION INSTRUCTIONS

* Disconnect battery before beginning installation.


1. Loosen top alternator mounting bolt sufficiently enough for the slotted bracket on the chrome alternator cover to slide between the alternator and bolt head.
2. Align bolt hole of the other chrome alternator cover bracket with unused holes on back side of alternator and thread supplied 10mm x 14mm bolt with 10mm washer through bracket and into alternator. We suggest using a thread locking compound on this bolt.

NOTE: Customer may have to apply pressure to cover for this hole to line up.

2a. If the unused top hole on back side of alternator does not have threads, which is common on 2001 and later models, use the supplied 5/16 thread forming bolt and 5/16 washer. Install by inserting 5/16 bolt through alternator bracket hole and into unthreaded top hole on back of alternator. Apply pressure to head of bolt with your thumb as you gently turn the bolt clockwise with a box end wrench. Do not use a socket wrench on this bolt. As the thread forming bolt takes a bite into the alternator, continue to gently tighten the bolt while still applying pressure with your thumb until the bolt head seats against the bracket. Do not over tighten. Remember, you are actually cutting the threads into the alternator with this bolt !!!
3. Securely tighten all bolts.

50103 D - DELUXE FUSE BOX COVER $189.00

This covers the top and all 4 sides of the fuse box. This "show quality" triple chrome plated 14ga. piece adds a custom look. It really looks good with our Battery Den Cover, item # 50160. To finish it off you may want to use our chrome Fuse Box knob Cap, item # 50150E
(Deep skirted on all four sides) Installs in about 10 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
1. Unscrew existing knob on top of fuse box top.
2. Remove this knob by prying and pulling knob straight out - knob will snap out of top.
3. Position Chrome Fuse Box Cover over factory fuse box top and insert original knob through both holes and reinstall on fuse box.
4. Tighten knob securely.

50104 - BATTERY COVER $124.00

This covers the top and front edge of the o.e.m. style side post battery. Constructed from 14 ga. steel and "show quality" triple chrome plated. This can be used by itself or used under our Battery Den Cover, item # 50160 for a supprise look. Installs in about 5 minutes. Fits 1997-2003

INSTALLATION INSTRUCTIONS
1. Clean top of battery with denatured alcohol.
2. Remove backing from self adhesive tape attached to back of cover.
3. Position chrome cover over battery with lip toward front of car and forward enough to align with front edge of foam battery wrap.
4. Carefully set chrome cover on battery and apply even pressure over cover. Car may be driven immediately but allow 24 hours for tape adhesive to cure.

50105 - BRAKE BOOSTER COVER $70.00

"Constructed of 14-gauge steel - precision cut and formed, then meticulously "show quality" triple chrome plated for a knockout look. Simple installation requires no modifications to your Corvette, secured using double sided tape. Installs in about 2 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
1. Clean top of brake booster with denatured alcohol.
2. Remove backing from self adhesive tape on back of cover.
3. Position cover evenly over brake booster.
4. Gently lower cover onto brake booster being careful to have equal amounts of cover on both sides of brake booster.
5. Apply even pressure to cover to adhere tape. Vehicle may be driven immediately but allow tape adhesive to cure for 24 hours.

50106 - IDLER PULLEY COVER $189.00

This piece cleans up the front passenger side of the engine. It covers the pulleys, belts and thermostat housing. Made of 14 ga. steel and "show quality" triple chrome plated for a show winning look. Attaches by using unused factory bolt holes. Installs in about 10 minutes. Fits 1997-2003, 2004.

INSTALLATION INSTRUCTIONS
1. Install the supplied 1/4" x 1" hex head bolt through the unused hole in the tab on the thermostat housing. The bolt should be installed from the back side of the tab with the threaded end toward the front of the car.
2. Loosely thread the 1/4" nut onto the 1/4" bolt, leaving it loose enough so the bolt can be moved up and down.
3. Install Chrome Cover by positioning cover over idler pulley and sliding the front bracket with the 9/32" hole over the 1/4" bolt, loosely install 1/4" lock washer and 1/4" nut.------DO NOT TIGHTEN at this time.
4. Position cover so the rear bracket with the slotted hole aligns with the unused hole in the cylinder head, install the supplied flat washer and 10mm bolt.-----IT IS STRONGLY SUGGESTED TO USE A THREAD LOCKING COMPOUND such as loctite on all nuts and bolts.
5. Tighten all nuts and bolts securely, making sure to tighten the first installed 1/4" nut tight against the thermostat housing.
6. The radiator hose may cause some interference with the installation on some cars. If this is the case, simply trim the end of the hose with a razor knife. It is not necessary to remove the hose.

50107 - MASTER CYLINDER COVER $189.00

This completely covers the plastic brake fluid reservoir. This piece is a work of art, it's our hardest piece to make but our effort clearly shows. Constructed from 16 ga. steel and "show quality" triple chrome plated. Simple installation. You can use our etched chrome Master Cylinder Cap, item # 50151E for a show winning apperance. Installs in 2 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove all grease and brake fluid from the outside of the master cylinder.
2. Remove fill cap from master cylinder.
3. Install Chrome Cover by positioning it over the master cylinder, align the hole in cover with master cylinder fill hole, press cover straight down until cover seats on top of master cylinder cover.
4. Replace cap on master cylinder fill hole.

50108 - POWER STEERING RESERVOIR COVER $189.00

This "show quality" piece is constructed from 16 ga. steel. It easly installs by removing the dipstick, sliding the cover over your reservoir and replacing your dipstick. You can use our etched chrome Power Steering Resevoir Cap, item # 50152E for a finished show winning look. Installs in about 2 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1- Remove all grease and fluid from the outside of the reservoir.
2. Remove fill cap dipstick from reservoir.
3. Install cover by positioning it over the power steering reservoir and align the hole in the cover with the reservoir fill hole, press cover straight down until cover seats on top of the reservoir.
4. Replace cap on reservoir.


 

50109 - THROTTLE BODY COVER $189.00

This piece covers the entire throttle body area. It fits flush with our Alternator Cover, item 50102 and our Idler Pulley Cover, item # 50106 making them appear to be one piece. This piece was designed to work in conjuntion with our Intake Cover, item 50101. Constructed from 14 ga. steel and "show quality" triple chrome plated. Installs in about 10 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Loosen the top bolt in the throttle body far enough for the throttle body bracket to slide between the bolt and the throttle body. Securely tighten bolt.
2. If you are also using Creative Engine Covers Intake Cover, Item # 50101, follow above procedure except slide the throttle body bracket between the bolt and the intake bracket. Press the throttle body bracket down as far as possible and hold in that position, adjust height of intake cover. While holding both covers in desired position, securely tighten bolt. The throttle body cover may be twisted after installation slightly up, down, left or right if necessary to align with any of our additional covers or to provide additional clearances.

50110 - Chrome ABS/AH Cover $94.00

Laser cut from 18 ga. steel and "show quality" triple chrome plated. This piece covers the unsightly tubes coming from the anti lock brake / active handling module located beneath the upper radiator hose. This piece is held in place with attached double sided tape. Installs in about 5 minutes. Fits 2000 - 2004 with active handling only

INSTALLATION INSTRUCTIONS
1. Remove the diagonal piece of 2 inch tape from the back of the cover and set aside with the sticky side up until the final step. 2. Trial fit the ABS/AH Cover by gently lifting the top radiator hose and sliding the Cover under the hose so that it lays on top of the tubes coming out of the top of the ABS/AH module. The curved end should follow the curve of the small hose by the moldule. Make sure the edges of the Cover are square with the pulleys and covers all tubes. 3.When you are satisfied with the way the Cover fits, remove the cover and peel the protective film from the back of the two attached pieces of tape and reposition the cover as you did in the trial fit. When it is poisitioned correctly press down on the Cover to adhere the tape to the tops of the tubes. 4. Place the piece of tape that you set aside in step 1 crossways under the tubes with the sticky side up and press it into the tubes and the bottom of the tape that was attached to the cover.

50111 - Hood Liner Retainer $129.00

This 15 piece kit is made using factory original hood liner retainers with chrome caps installed over them. This kit really makes your drab hood liner come to life. If you have a painted emblem or decal on your hood liner these retainers make them come alive. Installs in about 15 minutes. Fits 1997 to 2004.

INSTALLATION INSTRUCTIONS
1. Remove your existing hood liner retainers by inserting a retainer removal tool under the retainer or simply grasp the retainer with your finger tips and pull the retainer away from the hood until it comes out of the hole. Make sure you don't damage your hood liner as it is very soft and unforgiving. Remove one retainer at a time and replace it with a chrome retainer before proceeding to the next one. 2. Install the chrome retainer by simply inserting the pointed end into the empty hole and pressing on the chrome button end until it is fully seated against the hood liner. 3. Continue the above proceedures until all 15 chrome retainers are installed.

50112C - HOOD STRUTS COVERS (PAIR) $139.00

These chrome strut covers are machined from billet aluminum, highly polished and then "show quality" triple chrome plated. They fit perfectly over the barrel of your factory original strut. These are not the cheap thin stainless steel covers sold elsewhere. They are thick walled with machined rounded ends for a professional look. Installs in about 15 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1.Remove your hood strut by inserting a small bladed screw driver under the spring clip on the end of the strut where it attaches to the hood, gently pry this clip away from the strut end while pulling the strut away from the hood. When you have pried the spring clip far enough,the strut will come loose from the hood. You do not want to remove the spring clip entirely from the end. Repeat the above procedure for the bottom of the strut where it attaches to the frame. 2. Slide the Chrome Strut Cover over the strut until the ends align, you will notice that the Strut Cover fits very loosely. When you see how it should fit, remove the Strut Cover and wrap one or two layers of masking tape around each end of the strut barrel until the Strut Cover slides on and fits tightly. The Strut Cover will stay in place at this point. 4. Replace the strut end on the strut by screwing it on in a clock wise direction until tight. 5.Replace the strut on the car by simply pressing the strut ends over the ball sockets. There is no need to pry the spring away to reinstall. 5. Install the second strut by following the above procedure.

50113 - HOOD STRIKERS (PAIR) $119.00

These are brand new original equipment strikers. They are "show quality" triple chrome plated. Chrome replacement hex head bolts and washers are included. Installs in about 10 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove the two bolts from the existing strikers and remove striker.
2. Replace with chrome strikers and chrome replacement bolts and washers.

50114 - HOOD HINGES (PAIR) $629.00

These are brand new factory original hinges that have been "show quality" triple chrome plated. These are by far the best quality hinges that are available in the United States. No other company has this kind of quality. You won't be disappointed. Order our Chrome Hinge Replacement Bolt Kit, item # 50114B for a finished look. 1997 - 2004

INSTALLATION INSTRUCTIONS
1. Remove bolts from hinge and scribe the inner hole onto frame, one bolt at a time, replacing the bolt after scribing the mark.
2. After scribing all holes, remove all bolts and hinge.
3. Replace with chrome hinge, aligning holes to scribe marks.
4. Reinstall bolts.

50114B - HOOD HINGE BOLT KIT  $65.00

This kit consits of four hardened chrome replacement washers, four chrome replacement lock bolts, four chrome acorn nuts for the hinge connection to the frame and four hardened chrome replacement washers, four chrome replacement hex head bolts for the hinge connection to the hood. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Simply unscrew the bolts from the hinge where it attaches to the hood and replace those bolts with the chrome replacement bolts and chrome washers marked "hinge to hood. 2. Remove the nuts from the hinge where it attaches to the frame and replace them with the chrome washers, chrome lock nuts and finish up by screwing the chrome acorn nut on the remaing exposed portion of the stud for a finished look. These are marked "hinge to frame".  

50115 - HOOD LATCHES (PAIR) $294.00

These are brand new factory original hood latches, "show quality" triple chrome plated for a professional look. Installation time is about 30-40 minutes. Fits 1997 - 2004

INSTALLATION INSTRUCTIONS
1. Remove bolts from hinge and scribe the inner hole onto frame, one bolt at a time, replacing the bolt after scribing the mark.
2. After scribing all holes, remove all bolts and hinge.
3. Replace with chrome hinge, aligning holes to scribe marks.
4. Reinstall bolts.

50116 - 18 PIECE INNER FENDER CHROME SCREW KIT $45.00

This kit consists of 18 each chrome phillips head replacement screws and 18 each chrome washers. Installation time is about 20 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
Unscrew existing screws and replace with chrome screws and washers.

50117 - 6 PIECE FRONT BUMPER CHROME BOLT KIT $70.00

This kit consists of 6 each 5/16"X1" chrome hex head bolts, 6 each 5/16" chrome hardened washers, 6 each 5/16" zink plated flat washers and 6 each 5/16 zink plated lock nuts. You can use this bolt kit by itself or with our Chrome Front Bumper Insert, item # 50135. Installation time is about 15 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
Remove the six push pins in front bumper by inserting flat blade screw driver in slot and gently pry up middle button, then grasp the button with pliers and pull push pin out of hole. Replace with chrome bolts.

50118 - 5 PIECE COWL CHROME BOLT KIT $62.00

This kit consists of 5 each 5/16'X1" chrome hex head bolts, 5 each 5/16" chrome flat washers, 5 each 5/16" zink plated flat washers and 5 each 5/16 zink plated lock nuts. This bolt kit can be used alone for that suttle look or with our Chrome Cowl Insert, item # 50137. Installation time is about 20 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
Remove the five push pins in front bumper by inserting flat blade screw driver in slot and gently pry up middle button, then grasp the button with pliers and pull push pin out of hole. Replace with chrome bolts.

50119 - 9 PIECE GAS DOOR CHROME SCREW KIT $23.00

This kit consits of 9 each chrome phillips head replacement screws and 9 each chrome flat washers. This adds a nice touch when the judge opens your fuel door. Installation time is about 5 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
Remove existing screws and replace with chrome screws and chrome washers.

50120 - 16 PIECE REAR HATCH CHROME SCREW KIT $00.00 DISCONTINUED

This kit consists of 16 each chrome phillips head replacement screws and 16 each chrome flat washers. This adds a finished look to your rear hatch area. Installation time is about 25 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
Remove existing screws and replace with chrome screws and chrome washers.

50121 - TRUNK HINGES (PAIR) $499.00

These are brand new factory original trunk hinges that have been "show quality" triple chrome plated for a look that transforms your drab looking trunk into something you will be proud to open for folks to see. You can add our Chrome Trunk Hinge Bolt Kit, Item # 50121B and our Chrome Strut Covers, Item #50125C to give these Chrome Hinges a professional finished look. Installaation time is about 30 minutes for each hinge. Fits 1997 - 2004

INSTALLATION INSTRUCTIONS
1. Remove bolts from hinge and scribe the inner hole onto frame, one bolt at a time, replacing the bolt after scribing the mark.
2. After scribing all holes, remove all bolts and hinge.
3. Replace with chrome hinge, aligning holes to scribe marks.
4. Reinstall bolts.

50121B - TRUNK HINGE BOLT KIT  $55.00

This kit consists of eight chrome replacement hex head bolts, four small chrome replacement washers and four large chrome replacement washers. The Chrome Trunk Hinges, Item # 50121 are not complete without these chrome bolts and washers. These also add a nice touch to the black factory hinges. Instalation time is about 30 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
For installation instructions refer to the installation instructions on our Chrome Trunk Hinges, Item # 50121.

50122 - TRUNK STRIKER $64.00

This is a brand new original equipment striker, triple chrome plated. This comes complete with replacement chrome bolts and washers. This is a great inexpensive addition for the trunk. For verts, hardtops and Z06. Installation time is about 10 minutes. Fits 1998-2004.

INSTALLATION INSTRUCTIONS
1. Remove the two bolts from the existing striker and remove striker.
2. Replace with chrome striker and chrome replacement bolts and washers.

50123 - REAR HATCH STRIKERS (PAIR) $128.00

These are brand new factory original rear hatch strikers that have been "show quality" triple chrome plated for a true show quality appearance. These come complete with chrome replacement bolts and washers. Installation time is about 15 minutes. Fits 1997-1999.

INSTALLATION INSTRUCTIONS
1. Remove the two bolts from the existing striker and remove striker.
2. Replace with chrome striker and replace bolts with the supplied chrome replacement bolts and washers. 3. Repeat above procedure for second striker.

50124 - REAR HATCH STRIKERS Late (PAIR) $159.00

These are brand new factory original rear hatch strikers that have been "show quality" triple chrome plated. These come complete with chrome replacement bolts and washers for a true show quality appearance. Installation time is about 15 minutes. Fits 1999-2004.

INSTALLATION INSTRUCTIONS
1. Remove the two bolts from the existing striker and remove striker.
2. Replace with chrome striker and replace bolts with the chrome replacement bolts and washers. 3. Repeat above procedure for second striker.

50125C TRUNK STRUT COVERS - VERT and HARDTOP $139.00

These strut covers are machined from billit aluminum, highly polished and then "show quality" triple chrome plated. These are thick walled aluminum with machined rounded ends for a professional look. They are not the thin stainless covers sold elsewhere. These are a perfect compliment to the chrome trunk hinges, item # 50121. Installation time is about 40 minutes. Fits 1998-2004

INSTALLATION INSTRUCTIONS
1. Remove your existing trunk struts by inserting a flat bladed screw driver under the spring clip in the end of the strut where it attaches to the trunk lid. Gently pry the clip away from the strut while pulling the strut away from trunk lid. When the spring clip is far enough out the strut will come loose from the trunk lid. (DO NOT REMOVE THE SPRING CLIP ENTIRELY FROM THE STRUT).
2. Repeat the above procedure for the trunk strut where it attaches to the frame.
3. Grasp the large barrel end of the strut with a pair of pliers and while gently holding it tightly, grasp the plastic connector end with another pair of pliers and unscrew the end counter clockwise and remove it.
4. Slide the Chrome Strut Cover over the strut until the ends align, you will notice that the Strut Cover fits loosely. When you see how it should fit, remove the Strut Cover and wrap one or two layers of masking tape around each end of the strut barrel until the Strut Cover slides on and fits tightly.The Strut Cover should be in its final position at this point.
5.Replace the plastic connector end by screwing in on in a clock wise direction until tight.
6. Replace the strut on the car by simply pressing the strut ends over the ball connectors. There is no need to pry the spring clips to install.
7.Install the second Chrome Strut Cover by following the above procedure.

50126C  REAR HATCH STRUT COVERS (PAIR) $139.00

These strut covers are machined from billit aluminum, highly polished and then "show quality" triple chrome plated. These are thick walled aluminum with machined rounded ends for a professional look. These are not the thin stainless tubes sold elseware. These are the real deal. These will really dress up your rear hatch and can be seen even with the hatch closed. Installation time is about 40 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
1. Remove your existing rear hatch struts by inserting a flat bladed screw driver under the spring clip in the end of the strut where it connects to the hatch. Gently pry the spring clip away from the plastic end while pulling the strut away from the hatch. When the spring clip is far enough out the strut will come loose from the hatch.( DO NOT REMOVE THE SPRING CLIP ENTIRELY FROM THE STRUT)
2. Repeat above procedure where the strut attaches to the bottom hatch area.
3. Grasp the large barrel end of the strut with a pair of pliers and gently hold it tightly while grasping the plastic connector end with another pair of pliers and unscrew the plastic connector counter clockwise and remove it.
4. Slide the Chrome Strut Cover over the strut until the ends align. You will notice that the Strut Cover fits loosely at this point. When you see how it should fit, remove the Strut Cover and wrap one or two layers of masking tape around both ends of the barrel or until the Cover slides on and fits tightly. The Strut Cover will be in its final position at this point.
5. Replace the plastic connector end by screwing it on in a clockwise direction until tight
6. Replace the strut on the car by simply pressing the strut ends over the ball connectors. There is no need to pry the spring clips out to install.
7. Install the second Chrome Strut Cover by repeating the above instructions.


50127  AIR DUCT COULPER COVER $169.00

Lazer cut from 18 ga. steel, machine rolled to perfectly match the curvature of the factory rubber accordion air duct coupler. This looks great as a stand alone option or it will enhance any of our other chrome or painted products. This is is the only place that you will find a cover of this type. Installs in about 5 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Trial fit the Cover several times before removing the protective film from the tape.
2. Clean the top of the factory rubber accordion air duct coupler with denatured alcohol to remove any silicone products that may have been previously applied. The tape will not adhere to surfaces coated with these products unless cleaned.
3. Place the Air Duct Coupler Cover over the top of the factory rubber accordion coupler.
4. Slide the end of the Air Duct Coupler Cover as far back toward the throttle body as it will go.
5. Press down on the Air Duct Coupler Cover until it snaps over the rubber accordion coupler.
6. When you are satisfied with the way it fits, remove the protective film from the tape and reinstall the Air Duct Coupler Cover as before.
7. Press down on the Air Duct Coupler Cover in the area of the tape to make sure it adheres. Avoid movement of the Air Duct Coupler Cover for 24 hours to allow the adhesive to cure. Check Air Duct Coupler Cover after driving to make sure it is securely adhered.


50128  HOOD ACCENTS $104.00

For some thing that is really special and inexpensive try these little gems. These are lazer cut from 18 ga.steel and "show quality" triple chrome plated to accent your hood when open. These go great with our Hood Liner Retainers, Item # 50111 or just alone. Installs in about 5 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Position the Hood Accent on the end of the hood mounting pad that the hood hinges bolt to. On the end of the hood mounting pad is a shape that corresponds to the shape of the Hood Accent. There is a driver side and a passenger side Hood Accent.
2. Hold the correct Hood Accent over the hood mounting pad until you are sure of the way it should fit.
3. When you are sure of the way it should fit, clean the area of the hood mounting pad with denatured alcohol, peel the protective film from the double sided tape and position the Hood Accent on the hood as you did in step 2. Apply pressure to the Hood Accent with your hand to assure that the tape adheres to the hood.
4. Follow the above procedure for the second Hood Accent.

50129 CHROME ALTERNATOR $525.00

These are brand new alternators with "show quality" triple chrome plated cases and pulleys direct from the factory. These are not rebuilt or disasembled units. All units come with a one year factory warranty. This is for those that want the real deal instead of a cover. This Chrome Alternator has a show winning look by itself or when combined with our Chrome Alternator Bracket, Item # 50132 and our Chrome Alternator Bolt Kit, Item # 50132B. Installation time depends on which combined items you install. Fits 1997-2003 See the C6 section for 2004-2008 models.

INSTALLATION INSTRUCTIONS
Remove and replace alternator as per factory shop manual.

50130 DOOR LATCH SCREW KIT $89.00

This kit consists of six factory original screws that have been triple chrome plated for an added touch when you have your doors open.Installation time is about 10 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove an existing torx head screw and replace it with a chrome torx head screw. Only remove and replace one at a time to prevent your door latch from moving out of alignment.
2. When you finish replacing the three torx head screws on one door repeat the same procedure on the second door.


50131 - DOOR SUPPORTS (PAIR) DISCONTINUED

Constructed of 1/2 inch square steel, show quality triple chrome plated for an award winning appearance. If you want to show the interior of your car you have to have these Chrome Door Supports. Not only does it hold your doors open for the judges or spectators to see but it prevents the wind from blowing the doors into other cars and prevents people from getting into your car. Installs and removes in just seconds. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Install with door open.
2. Insert door support into door striker with the slot in end facing up, lower support down until second slot rest on striker and the door support is level.
3. Pull door handle to open door latch, slip bolt on end of support into door latch and release door handle. Remove by reverse procedure.

50132 - ALTERNATOR BRACKET $390.00

Show quality triple chrome plated OEM replacement alternator bracket. 1997 - 2004

INSTALLATION INSTRUCTIONS
Remove alternator and bracket as per shop manual and install chrome alternator bracket.

50132B - CHROME ALTERNATOR BRACKET BOLTS $84.00

This kit consists of the four factory Alternator Bracket Bolts that can readily be seen after installation of the Chrome Alternator Bracket. The heads of these bolts have been sanded smooth before they were triple chrome plated. This kit is necessary to finish the look of the Chrome Alternator Bracket or the Chrome Alternator. They look good with the factory bracket and alternator as well. Installation time depends on which other Alternator components are installed along with the bolts. Fits 1997-2004

INSTALLATION INSTRUCTIONS
Simply remove one factory bolt and replace with one chrome bolt at a time.

50133 - DOOR STRIKERS (PAIR) $149.00

These are brand new factory original sreikers, "show quality" triple chrome plated for a show winning look. Chrome replacement bolts are included. You can use our chrome Door Supports, item # 50131 to go along with the strikers. Installation time is about 15 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove the two bolts from the existing striker and remove striker.
2. Replace with chrome striker and chrome replacement bolts.

50134 - CHROME UPPER RADIATOR SUPPORT $535.00

This is a factory original plastic part that has gone through our special "show quality" triple chrome plating process. This piece along with the chrome Air Duct, item # 50138 puts your engine compartment way above your competitors. This is an eye popping look. Installation time is about 30 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove air duct and four bolts holding support and remove support.
2. Install chrome support in reverse procedure.

50135 - CHROME FRONT BUMPER INSERT $174.00
 
This piece is fabricated from laser cut 16 ga. steel and "show quality" triple chrome plated ....... THIS IS NOT THIN STAINLESS. You can use our Front Bumper Chrome Bolt Kit , item # 50117 for a finished look. Installs in about 15 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
Remove the six push pins from front bumper. Position chrome insert and reinstall the six push pins or order our matching chrome bolt and washer kit, item # 50117 for a finished look.
50136 - CHROME DOOR HANDLES (pr) $569.00
 
These factory original door handles are disasembled, "show quality" triple chrome plated and reassembled for a very expensive, elegant look. For the owner that want an extra special look that not every one has. Installation time is about 90 minutes. Fits 1997-1999 and 2000-2004.

INSTALLATION INSTRUCTIONS
Remove your door handles and replace with our Chrome Door Handles as per shop manual.

50137 - CHROME COWL INSERT $199.00
 
This two piece part is fabricated from laser cut 16 ga. steel and "show quality" triple chrome plated. It has beautifully proportioned slots for the hvac air intake.They also match the slots in our new chrome Battery Den Cover, item # 50160. You can use our Cowl Chrome Bolt Kit, item # 50118 to finish the look. Installation time is about 15-20 minutes Fits 1997-2004.

INSTALLATION INSTRUCTIONS
Remove the five push pins from the cowl and then position the cowl insert on the cowl and reinstall the five push pins or order our matching chrome bolt and washer kit Item # 50118 for a finished look.

50138 - CHROME AIR DUCT $379.00

We turn your stock air duct into a show quality triple plated master piece. This is a piece that you absolutely have to have. It makes the engine compartment along with the Chrome Radiator Support, item # 50134. Send us your original air duct and we will "show quality" triple chrome plate it for you with a quick turn around. Instalation is about 30 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove your existing air duct by unscrewing the worm clamps on the rubber accordian air duct coupler where it attaches to the throttle body and where it attaches to the mass air flow sensor.
2. Gently rock the air duct back and forth while lifting the air duct straight up and working the rubber connectors off of the throttle body and mass air flow sensor. The air duct will slip off of the two rubber grommets holding it to the radiator support.
3. Once the air duct is off the car, remove the rubber accordian coupler from the duct.
4. Replace with your Chrome Air Duct following the above procedures in reverse.

50139 DOOR BEZELS $439.00
Special Order

These are factory original plastic inside door bezels that have gone through our special plastic plating process. They are now finished in "show quality" chrome for the exquisite touch that no one else has. Installation time is about 15 minutes per side. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
These are easy to install. Follow our included instructions.

50141 - HOOD ADJUSTMENT BOLTS $108.00

This kit consists of all four of the Hood Adjustment Bolts, four nuts and four rubber bumpers. These are brand new factory original bolts that have been triple chrome plated. If you have chrome hinges or chrome safety hood stops these will give them a finished, professional look. If you don't have the chrome hinges or stops yet, these will really accent your factory black parts. Don't forget, it's the attention to small details that make a show winner!!! Installation time is about 20 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
1. Count the threads on each Hood Adjustment Bolt above the nut.
2. Loosen the nut with a wrench 1 turn and unscrew the bolt from the hinge or safety stop with your fingers.
3. Adjust the nut on the Chrome Hood Adjustment Bolt so the same amount of threads are above the nut as were on the original bolt.
4. Screw the Chrome Hood Adjustment Bolt into the hinge or safety stop until the nut makes contact with the surface, then tighten the nut with a wrench.
5. Repeat the above procedure with the 3 remaining bolts

50142 Hood Insert $199.00

This two piece part is laser cut from 16 ga. steel and "show quality" triple chrome plated. The Hood Insert goes on the inside top of the hood where it captures everyones attention when the hood is raised. The slots in this part match the slots in our Hood Insert #50137 and our Battery Compartment Cover #50160 so it tastefully ties everything together.

INSTALLATION INSTRUCTIONS
This product is installed utilizing the attached double sided 3M tape. Make sure that the section of the hood where this fits is very clean with no grease or wax that will prevent the tape from adhereing properly. You can use alcohol for this.
1. Before removing the protective film from the tape on the Hood Insert, place the large half of the Insert on the top inside of the hood on the driver side aligning the shape of the insert to the like shape on the hood. There should be a slight gap between the Insert and the hood on the big end, this is the way it is designed. When you are satisfied with the way it should fit proceed to the passenger side and place the small half of the insert at the top of the hood matching the shape of the insert with the like shape on the hood.
2. When you are completely satisfied with the way the parts should fit remove the protective film from the double sided 3M tape on the large part of the Insert and slowly position it on the hood in the desired position. DO NOT PRESS HARD ON THIS PART AT THIS TIME IN CASE YOU HAVE TO MOVE IT!!!
3. Remove the protective film from the 3M tape on the small part and place it on the hood in the desired position making sure the small ends of both parts line up and touch each other. DO NOT PRESS HARD ON THIS PART AT THIS TIME IN CASE YOU HAVE TO MOVE IT.
4. When both parts are in perfect position, press hard on the parts with a micro fiber towel to make sure that the tape adheres to the hood.
Installation time is about 20 to 30 minutes. Fits 1997 - 2004

50144 - CHROME WHEEL WELL COVERS (pr) $375.00

Fabricated from laser cut 18 ga. steel, meticulously hand formed to fit the curvature of the fender well then "show quality"triple chrome plated for an award winning look. Installation time is about 10 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
Clean the tops of the wheel wells with denatured alcohol to remove any silicone products that may have been previously applied. 1. Trial fit either the driver side or the passenger side Chrome Wheel Well Cover by simply laying it over your wheel well starting at the front of the wheel well and laying it down towards the rear.. The outer edge should fit tight against the inside of the fender.
2. When you are satisfied with the way it looks and fits, remove the cover and peel the protective film from the Velcro strips ( DO NOT SEPERATE THE VELCRO HALVES ) ,now reinstall the cover as you did in the trial fit.
3. Press down on the cover with your hand and a towel in the areas of the Velcro strips to make sure the adhesive on the Velcro makes good contact with your wheel well and adheres properly.
4. Install the second cover following the apove procedure. Do not remove the covers for 24 hours to give the Velcro adhesive time to cure.

50147  REAR SWAYBAR STRAP KIT  $190.00
 
These are brand new factory original straps and bolts.  Triple chrome plated for killer look from the rear.Installation time is about 45 minutes Fits 1997-2004.
 
INSTALLATION INSTRUCTIONS
Simply remove the existing nut and bolt from strap and remove.  Replace with new chrome strap, new chrome nut and new chrome bolt. Repeat above procedure for second strap.
50148  CHROME DIP STICK HANDLE $64.00
 
Triple chrome plated handle with a smooth top for a show winning touch. Installation time is less than 5 minutes. Fits 1997-2004
 
INSTALLATION INSTRUCTIONS
Remove existing handle from dipstick by tapping out roll pin in handle with supplied tool.  Install new chromed handle on dipstick and reinsert roll pin.  Takes less than 2 minutes to install.
50149 SECONDARY AIR CHECK VALVE $349.00

This piece is the factory original secondary air check valve and pipe, it includes two chrome bolts and a gasket. This piece finishes the driver side of the engine compartment. Installation time is about 15 minutes. Fits 1997-1998, 1999-2000, 2001-2004

INSTALLATION INSTRUCTIONS
1. Loosen plastic clamp that secures the rubber hose by inserting a flat bladed screw driver between the serrated halves and twisting the screw driver until the two serrated pieces seperate and the clamp loosens enough to slide it along the rubber tube away from the check valve.
2. Remove the rubber hose by grasping it with your fingers and with a twisting motion pull it off of the check valve. ( there is no fluid in this rubber hose )
3. Remove the two bolts from the check valve and remove it from the car. Scrape any of the old gasket material from the head before proceeding to the next step.
4.Install the Chrome Secondary Air Check Valve by positioning it on the head with the new supplied gasket and insert the supplied Chrome Bolts into the holes and torque to manufactors specifications.
5. Re install the rubber hose by sliding it onto the Check Valve , then slide the plastic clamp into its original position and tighten by squeezing it closed with a pair of pliers.

50150  CHROME FUSE BOX CAP $49.00

These domed caps are machined from billet aluminum and show quality triple chrome plated.  These are the best caps on the market, not thin stamped stainless steel.  

INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  The caps can be easily removed if necessary when you take your car in for service or when you add fluids.

50151  CHROME MASTER CYLINDER CAP $49.00
 
These domed caps are machined from billet aluminum and show quality triple chrome plated.  These are the best caps on the market, not thin stamped stainless steel.  

INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  The caps can be easily removed if necessary when you take your car in for service or when you add fluids.

50152  CHROME POWER STEERING CAP $49.00

These domed caps are machined from billet aluminum and show quality triple chrome plated.  These are the best caps on the market, not thin stamped stainless steel.  

INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  The caps can be easily removed if necessary when you take your car in for service or when you add fluids.
50153  CHROME COOLANT CAP $49.00

These domed caps are machined from billet aluminum and show quality triple chrome plated.  These are the best caps on the market, not thin stamped stainless steel.  

INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  The caps can be easily removed if necessary when you take your car in for service or when you add fluids.
50154  CHROME ENGINE OIL CAP $49.00
 
These domed caps are machined from billet aluminum and show quality triple chrome plated.  These are the best caps on the market, not thin stamped stainless steel.  

INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  The caps can be easily removed if necessary when you take your car in for service or when you add fluids.
50155  CHROME WASHER FLUID CAP $49.00
 
These domed caps are machined from billet aluminum and show quality triple chrome plated.  These are the best caps on the market, not thin stamped stainless steel.  

INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  The caps can be easily removed if necessary when you take your car in for service or when you add fluids.
50156  CHROME HYD. CLUTCH CAP $49.00
 
These domed caps are machined from billet aluminum and show quality triple chrome plated.  These are the best caps on the market, not thin stamped stainless steel.  

INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  The caps can be easily removed if necessary when you take your car in for service or when you add fluids.
50157  GAS TOP CAP $75.00
 
This unique domed cap is machined from billet aluminum, highly polished, then triple chrome plated. It is designed to snap over your existing gas tank filler cap. This provides a special look, especially when combined with our Painted Gas Door Boot, Item # 53315 and our Gas Door Screw Kit, Item # 50119. If you want to show case a part of your car that is sure to catch the judges eye, this is it !!! Installation time is about 2 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. This cap is designed to snap over your existing gas cap and it also has a Velcro tab attached to a recessed grove inside of the cap.
2. Rotate the lanyard that is attached to your existing cap to the top or 12 o'clock position of your cap. Do not remove the cap from the car.
3. Place the Chrome Gas Cap over the existing cap by first putting the cut out section at the top and over the lanyard attachment point.
4. Lower the bottom of the Chrome Cap into position and press on the bottom until it snaps into place.
5. When you are satisfied with the fit remove the cap in reverse order and remove the protective film from the Velcro tab and reinstall as before.
50158  HEAD LIGHT KNOB CAPS (PR) $125.00
 
This set of two caps are machined from billet aluminum,highly polished and triple chrome plated for a show winning look. These caps have domed tops to match the other caps in our line. They are really thick walled caps, not like the thin stainless steel caps on the market. These caps will not interfere with the operation of your head lights as some other brands do. Installation time is about 5 minutes. Fits 2000-2004.

INSTALLATION INSTRUCTIONS
1. Simply slide each Chrome Cap over each of your head light manual adjustment knobs.
2. Press on the Chrome Cap with your hand until the cap goes all the way to the bottom. These caps are a tight pressure fit but if they should fit loose on your particular car just put a wrap of masking tape around the head light knob prior to installing the cap.
50159  A/C PORT CAPS (PR)  $85.00
 
These two Chrome Air Conditioning Recharge Port Caps are machined from billet aluminum, highly polished and triple chrome plated for the best finish possible. They have thick walls for a serious look, not like the thin stamped stainless ones on the market. They also have domed tops to match the other caps in our line. Installation time is about 2 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Simply press the Chrome A/C Port Caps over your existing caps until they go completely down.
2. If they do not fit tightly, just wrap one or two layers of masking tape around your existing caps and reinstall the Chrome A/C Caps for a tight fit. They have to fit tight to prevent them from coming loose when you hit a major bump in the road.

50150-E  ETCHED CHROME FUSE BOX CAP $79.00
 
These caps are machined from billet aluminum and show quality triple chrome plated.  They are then etched with similar but better text than original caps.  These caps will give your car a "knock your socks off look" and are the absolute best caps on the market, not thin stamped caps.
 
INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  They can be easily removed if necessary when you take your car in for services.
50151-E  ETCHED CHROME MASTER CYLINDER CAP $79.00
 
These caps are machined from billet aluminum and show quality triple chrome plated.  They are then etched with similar but better text than original caps.  These caps will give your car a "knock your socks off look" and are the absolute best caps on the market, not thin stamped caps.
 
INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  They can be easily removed if necessary when you take your car in for services.

50152-E  ETCHED CHROME POWER STEERING CAP $79.00

These caps are machined from billet aluminum and show quality triple chrome plated.  They are then etched with similar but better text than original caps.  These caps will give your car a "knock your socks off look" and are the absolute best caps on the market, not thin stamped caps.
 
INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  They can be easily removed if necessary when you take your car in for services.
50153-E  ETCHED CHROME COOLANT CAP $79.00
 
These caps are machined from billet aluminum and show quality triple chrome plated.  They are then etched with similar but better text than original caps.  These caps will give your car a "knock your socks off look" and are the absolute best caps on the market, not thin stamped caps.
 
INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  They can be easily removed if necessary when you take your car in for services.
50154-E  ETCHED  CHROME ENGINE OIL CAP $79.00
 
These caps are machined from billet aluminum and show quality triple chrome plated.  They are then etched with similar but better text than original caps.  These caps will give your car a "knock your socks off look" and are the absolute best caps on the market, not thin stamped caps.
 
INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  They can be easily removed if necessary when you take your car in for services.
50155-E  ETCHED  CHROME WASHER FLUID CAP $79.00
 
These caps are machined from billet aluminum and show quality triple chrome plated.  They are then etched with similar but better text than original caps.  These caps will give your car a "knock your socks off look" and are the absolute best caps on the market, not thin stamped caps.
 
INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  They can be easily removed if necessary when you take your car in for services.
50156-E  ETCHED  CHROME HYD. CLUTCH CAP $79.00
 
These caps are machined from billet aluminum and show quality triple chrome plated.  They are then etched with similar but better text than original caps.  These caps will give your car a "knock your socks off look" and are the absolute best caps on the market, not thin stamped caps.
 
INSTALLATION INSTRUCTIONS
These caps are held in place with supplied Velcro tabs attached to recessed grooves inside of caps.  They can be easily removed if necessary when you take your car in for services.
50180  SUPERCHARGER COOLANT CAP $95.00
 

This is a cap that you probably won't find any where else. It is machined from billet aluminum, highly polished and "show quality" triple chrome plated for a show winning look. This has a lip machined around the bottom to completely cover your entire cap. It also has a domed top to match our other caps. There is a machined grove on the inside of the cap with a Velcro disk that holds it in place.Installation tine is about 2 minutes. Fits most supercharger coolant tanks 1997-2004.

INSTALLATION INSTRUCTIONS
1. Simply press the Chrome Cap over your existing cap, if it does not fit tightly remove it and place one or two wraps of masking tape around your existing cap until it does fit tight.
2. Remove the protective film from the attached Velcro tab and install the cap (do not separate the Velcro halves), press down on the cap with your hand to assure that the Velcro adheres to your cap.

50160 BATTERY COMPARTMENT COVER $199.00

This piece really makes the battery compartment area stand tall. Lazer cut from 18 ga. steel and "show quality" triple chrome plated for a show winning look. There are thirteen slots in this cover that match the slots in our Cowl Insert, Item 50137. For a dynamite look, use our regular Battery Cover, Item # 50104 under this Compartment Cover with an emblem placed on the top of the regular Battery Cover so it can be seen when looking down through the slots of the Battery Compartment Cover. WOW !!! Installation time is about 15 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove the rubber weather strip gasket from the battery compartment by grasping it on one end and pulling it straight up until it seperates from the battery compartment wall.
2. Insert the back end of the Battery Compartment Cover under the cowl and lower the cover so that it rests on the lip in the battery compartment wall and on the base of the rubber hood bumper at right rear. The left front corner of the cover will not rest on the battery compartment lip at this time. The rubber weather strip gasket will hold this corner down on the lip when you reinstall it.
3. When the cover is in place and seems to look like it is aligned properly, remove the cover and peel the protective film from the three Velcro strips. DO NOT SEPERATE THE VELCRO HALVES. Reinstall cover as before while pressing the side of the plastic battery compartment wall tight against the cover and press down in the area of the Velcro so it will adhere to the lip on the side of the battery compartmeny wall and be tight against the side of the wall. Reinstall the rubber weather strip by starting at one end and pressing it down onto the edge of the battery compartment wall as you work toward the other end.

50161 Rear Hatch Strut Brackets (PR) $329.00
SPECIAL ORDER


These are factory original strut brackets and ball studs that have been triple chrome plated. They come with chrome hex head replacement bolts and chrome replacement washers. These chrome brackets really add a nice touch to your rear hatch area and can be seen with the hatch open or closed. For an outstanding look, combine them with our Chrome Rear Hatch Strut Covers, item # 50126C. Installation time is about 30 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Remove one of your rear hatch struts from the bracket by inserting a small flat blade screw driver under the retainer clip located on the black plastic end of the strut and prying it away from the strut while pulling the strut away from the bracket. When the clip has been pried far enough the strut will come off of the bracket stud.
2. Remove the two torx head screws from the bracket and remove the bracket.
3. Install the Chrome Bracket using the two Chrome Replacement Hex Head Bolts and Chrome Washers.
4. Replace the strut by placing the plastic end on the ball stud and pressing on it with your hand until it snaps in place.
5. Repeat the above instruction for the other side.



50162 Alt Bracket Cover $195.00

This part is fabricated from 16 ga. steel and hand formed for a perfect fit, then "show quality" triple chrome plated for the perfect look. It covers all of the unsightly alternator bracket that can be easily seen. This piece comes with a chrome replacement top alternator bolt that secures the bracket cover in place. You can't go wrong with this cover and you don't have to go through the trouble of removing your alternator bracket to replace it with a chrome one. You don't have to remove the alternator to install this.
Installation time is about 20-30 minutes Fits 1997-2004

INSTALLATION INSTRUCTIONS
1. Remove driver side fuel rail cover by grasping the bottom and lifting until it releases from its retainers.
2. Remove the top bolt from the alternator bracket that secures the alternator to the bracket.
3. If you have a "chrome" alternator we recommend that you paint the front edge of the alternator bracket black as well as the wish bones that the "chrome" alternator attaches to before proceeding to step 4. If you do NOT have a "chrome" alternator, disregard this step.
4. Insert the Chrome Alternator Bracket Cover over the alternator bracket by sliding the small top end down below the throttle body while positioning the front of the cover between the bracket and the belt. You have to make sure that the small front tab on the cover goes behind the pully, if it goes forward of the lip on the pully and contacts it, you will not be able to install it. Line up the bolt holes in the cover with the bolt holes in the bracket.
5. When you are satisfied with the fit, place a supplied chrome washer on the supplied chrome bolt and insert the bolt through the front hole of the Cover and into the bracket. Tighten bolt securely. Insert the second supplied chrome washer over the protruding end of the bolt and thread the supplied chrome lock nut onto the bolt and tighten until it is snug. D0 NOT OVER TIGHTEN. PLEASE MAKE SURE THAT THE COVER DORS NOT INTERFERE WITH THE ROTATION OF THE BELT.
6. Reinstall the fuel rail cover by placing the top hooks on the cover under the fuel rail and pressing the bottom of the fuel rail cover until it snaps into its retainers. Make sure the bottom front corner of the fuel rail cover is BELOW the chrome nut before pressing into retainers.

50163-A Pillar Trim $129.00

Coming Soon.

INSTALLATION INSTRUCTIONS
Coming Soon.

50170 WINDSHIELD WIPER ARMS $650.00
Special Order
These are the factory original windshield wiper arms, blade assembly and replacement caps, all show quality triple plated for a show winning appearance. Includes new wiper blades. Installation time is about 15 -20 minutes per side. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
These are very easy to install. Before you begin, mark the positipn of your wiper blades by applying a strip of tape on your windshield next to your blades. 1. Remove the wiper arm nut cap by pulling straight up with your finger tips.
2.Remove the nut holding the arm to the stud.
3. Raise the wiper arm up and away from the windshield and while holding it in this position with one hand place the fingers of your other hand under the arm where it slips over the stud and forceably pull it up and off of the stud. Some times they may be stuck and you will have to jerk on it but be sure you are pulling straight up and not putting it in a bind by pulling it crooked.
4. Install the Chrome Wiper Arm by slipping it over the stud and pushing it all the way down making sure the blade aligns with the tape on the windshield. When you are satisfied with the way it looks and fits, install the nut and tighten, install the replacement nut cap.
5. Replace the other side following the above instructions.

50171 DOOR STRIKER BEZELS $360.00

These are factory original pieces that have gone through our special chroming process that transforms the ugly texured black plastic to beautiful smooth "show quality" triple chrome plated pieces. These compliment our Chrome Door Strikers, Item 50133. If you open your doors at shows, you really need these. Installation time is about 10 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
These are really simple to install. 1. Remove the existing striker bezels by carefully inserting a thin blade screw driver behind the striker bezel and with a twisting motion, pry the striker bezel away from the door jam. When you can get your finger tips under it just pull it off of the door jam. It is only held on with hook and loop material. YOU DO NOT HAVE TO REMOVE THE DOOR STRIKER !!!
2. To install the Chrome Door Striker Bezel, simply position new hook and loop material on bezel and press bezel over the striker making sure the bezel fits tightly against the door jam.
3. Repeat above procedure for the second bezel.

50174 Brake Pad Covers $85.95

Constructed from laser cut mirror finished stainless steel. These chrome like covers will really accent your painted brake calipers and draw attention to your wheels.
Installation time varies upon the individuals mechanical skills. Fits 1997-2004

INSTALLATION INSTRUCTIONS
1. Raise your Corvette with a jack or lift and remove a wheel.
2. Loosen both caliper retaining bolts but do not remove.
3. Remove top bolt only.
4. Rotate caliper just enough to expose the front of your factory brake pad.
5. Place the Brake Pad Cover over the brake pad. If the holes in the cover align with with the rivets smear a dab of silicone on the back of the cover and place it on the pad. If the holes do not align with the rivets then the pads need to be removed from the caliper and the rivets need to be ground off so the cover fits flush with the pad. The rivets are not necessary to hold the pads together as they are bonded.
6. Reposition brake caliper and tighten bolts securely.
7. Follow steps 1 through 6 for remaining three wheels



50182 FRONT FRAME RAIL COVER $275.00

These panels are laser cut from 16 ga. steel and "show quality" triple chrome plated. These panels will surley accent any sill plates that you may be using. Installation time is about 10 minutes. Fits 1997 - 2004.

INSTALLATION INSTRUCTIONS
1. Trial fit the Chrome Door Jam Panel on the correct side of the car. There is a left and a right side panel which is marked on the back of each panel. The side of the panel towards the inside of the car should maintain a 1/8 inch gap top to bottom from the inside lip.
2. When you are satisfied with the fit, mark the top and bottom of the panel location with small pieces of tape.
3. Remove the protective film from the attached tape and adhere the panel to the door jam in your desired position. Be certain the panel rests only on the flat surface of the door jam. If it rests on the bottom curved section of the door jam it will be raised off of the jam and may be contacted by the closure of the door marring the chrome finish.
4. Press on the Chrome Door Panel in the location of the tape to insure that it adheres to the door jam.
5. Repeat above procedure for the remaining door jam.



50183 SIDE FRAME RAIL COVERS $225.00

This piece is constructed from lazer cut 18 ga. stainless steel, machine formed to fit the curvature of the bottom of your front bumper. It is securely held in place with existing factory bolts and 3m tape. This bracket comes complete with a chrome license plate frame, license plate screws and lock nuts plus four chrome caps to cover the license plate screw heads. This bracket does not touch any part of your exposed body and the mounting can hardly be seen. It looks like it should have come with the car from the factory. Installation time is about 15 -20 minutes. Fits 2005-2012.

INSTALLATION INSTRUCTIONS
This comes with complete instructions


50185 FRAME RAIL ACCENTS $99.00

For some thing that is really special and inexpensive try these little gems. These are lazer cut from 18 ga.steel and "show quality" triple chrome plated to accent your hood when open. These go great with our Hood Liner Retainers, Item # 50111 or just alone. Installs in about 5 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Position the Hood Accent on the end of the hood mounting pad that the hood hinges bolt to. On the end of the hood mounting pad is a shape that corresponds to the shape of the Hood Accent. There is a driver side and a passenger side Hood Accent.
2. Hold the correct Hood Accent over the hood mounting pad until you are sure of the way it should fit.
3. When you are sure of the way it should fit, clean the area of the hood mounting pad with denatured alcohol, peel the protective film from the double sided tape and position the Hood Accent on the hood as you did in step 2. Apply pressure to the Hood Accent with your hand to assure that the tape adheres to the hood.
4. Follow the above procedure for the second Hood Accent.



50189 Door Jam Panels $190.00 pr.

These panels are laser cut from 16 ga. steel and "show quality" triple chrome plated. These panels will surley accent any sill plates that you may be using. Installation time is about 10 minutes. Fits 1997 - 2004.

INSTALLATION INSTRUCTIONS
1. Trial fit the Chrome Door Jam Panel on the correct side of the car. There is a left and a right side panel which is marked on the back of each panel. The side of the panel towards the inside of the car should maintain a 1/8 inch gap top to bottom from the inside lip.
2. When you are satisfied with the fit, mark the top and bottom of the panel location with small pieces of tape.
3. Remove the protective film from the attached tape and adhere the panel to the door jam in your desired position. Be certain the panel rests only on the flat surface of the door jam. If it rests on the bottom curved section of the door jam it will be raised off of the jam and may be contacted by the closure of the door marring the chrome finish.
4. Press on the Chrome Door Panel in the location of the tape to insure that it adheres to the door jam.
5. Repeat above procedure for the remaining door jam.

50193 Door Trim Molding $45.00

This is chrome coated flexable vinyl molding. It easily conforms to the intended shapes of use. Each piece has 3M brand automotive tape applied to the backing for easy installation.
Installation time is about 10 minutes per side. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
1. Trial fit one piece of the Door Trim Molding inside of your door on the door jam. DO NOT REMOVE THE RED PROTECTIVE FILM AT THIS TIME.
2. Install by inserting the end of the molding on the door jam at the rear vertical section where the 1/2 inch wide raised section starts at the bottom of the black plastic factory molding. Lay the Door Trim Molding on the raised section, keeping it tight against the black plastic, following it down, across the sill area and back up on the front section where it runs into the black factory molding.
3. Remove the red protective film about one foot and start applying the door Trim Molding as you did in the trial fit. Remove more of the red film and stick the molding as you go until you complete one side.
4. Repeat the same procedure for the remaining side.

50194 Mirror Trim Molding $30.00 pr.

These are chrome coated flexable vinyl trim moldings. They easily conform to the shape of the mirrors. Each piece has 3M brand automotive tape applied to the backs for easy installation. What a stunning look these molding will give to your car.
Installation time is about 10 minutes for each side. Fits 1997-2004

INSTALLATION INSTRUCTIONS
1. Trial fit these moldings before actually installing them so you become familiar with how they should look. DO NOT REMOVE RED PROTECTIVE FILM AT THIS TIME.
2. Install by peeling about two inches of the red protective film from one end of the molding. Start the end of the Mirror Trim Molding at the center of the bottom of the mirror housing working the molding toward the window. You will have to keep your thumb on the edge of the mirror housing to guide the molding and keep it even with the edge of the mirror housing. As you go around the window side of the mirror, this will be the most difficult part of the installation. You will have to manipulate the molding for it to conform with the irregular shape at this point making sure that you press the molding tight against the mirror as you go to ensure that it adheres.
3. Continue on around the mirror pulling a little of the red protective film loose as you go and adhering the molding by pressing it to the surface of the mirror housing and keeping it even with the edge.
4. As you get to the bottom, peel the rest of the protective film from the molding and without letting the molding contact the bottom of the mirror, butt the finishing end to the end that you started with and then press the molding to the bottom. There should have been a small amount of slack in the molding after butting the ends. This is there to compensate for any future shrinkage.
5. Repeat the above procedure for the remaining side.

50301 CHROME WASHER RESERVOIR $529.00

This is a magneficant looking piece. This piece is finished in extra heavy triple plated chrome for a look you won't believe. You won't see many cars with these, so if you want something unique, this is for you. Installation time is about 10 minutes. Fits 1997-2004

INSTALLATION INSTRUCTIONS
This piece is very easy to install. Make sure the top of your washer tank is clean of any silicone products by wiping with denatured alcohol. 1. Remove the washer tank refill lid by lifting straight up until the retainer ring snaps off of the washer tank fill hole.
2. Simply set the Chrome Washer Tank Cover over the washer tank and gently rock back and forth until the cover slips into place. When you are satisfied with the way it looks and fits remove the Cover .
3. Remove the protective film from the attached Velcro (DO NOT SEPERATE THE VELCRO HALVES) and reposition the Cover as in step 2 , firmly press down on Cover in the area of the Velcro strips to make sure that the adhesive adheres to your washer tank. Do not remove for 24 hours to give Velcro adhesive time to cure.

50302 CHROME RADIATOR SURGE TANK $465.00

This is a magneficiant looking piece. This piece is finished in extra heavy triple plated chrome for a look that you won't believe. You won't see many cars with these, so if you want something unique, this is for you. Installation time is about 10 minutes. Fits 1997-2004.

INSTALLATION INSTRUCTIONS
This piece is very easy to install. Make sure the top of your surge tank is clean of any silicone products that might have been previously applied. Do this by wiping with denatured alcohol. 1. Remove the coolant tank fill cap.
2. Simply set the Chrome Coolant Tank Cover in place over the coolant tank.
3. When you are satisfied with the way it fits and looks remove the cover and remove the plastic film from the attached Velcro strips. ( DO NOT SEPERATE THE VELCRO HALVES ) .
4. Reposition the cover as in step 2., firmly press down on the cover in the area where the Velcro is to make sure that the adhesive on the Velcro adheres to your coolant tank. Do not remove cover for 24 hours to give the Velcro adhesive time to cure.

To order, phone 804-763-6288.
We accept VISA, MasterCard, money orders and checks
and remember...CHROME WINS!!!
 

Tip: For best appearance and long life always keep a good coat of wax on all chrome parts.

User accepts any and all liabilities resulting from the use of Creative Engine Covers, Inc. products. Creative Engine Covers, Inc. is not liable for damages to property or injury to persons resulting from the use of our products. The user agrees to these terms by the act of using these products.
 

Back to Top.

Home | C7 Products | C6 Products | C5 Products | Accessories | Customer Cars
Terms | Links | About Us | Contact Us

Creative Engine Covers, Inc. 2000 - 2014